nat — Shorewall one-to-one NAT file




This file is used to define one-to-one Network Address Translation (NAT).


If all you want to do is simple port forwarding, do NOT use this file. See Also, in many cases, Proxy ARP (shorewall-proxyarp(5)) is a better solution that one-to-one NAT.

The columns in the file are as follows (where the column name is followed by a different name in parentheses, the different name is used in the alternate specification syntax).


External IP Address - this should NOT be the primary IP address of the interface named in the next column and must not be a DNS Name.

If you put ?COMMENT in this column, the rest of the line will be attached as a comment to the Netfilter rule(s) generated by the following entries in the file. The comment will appear delimited by "/* ... */" in the output of "shorewall show nat"

To stop the comment from being attached to further rules, simply include ?COMMENT on a line by itself.

INTERFACE - interfacelist[:[digit]]

Interfaces that have the EXTERNAL address. If ADD_IP_ALIASES=Yes in shorewall.conf(5), Shorewall will automatically add the EXTERNAL address to this interface. Also if ADD_IP_ALIASES=Yes, you may follow the interface name with ":" and a digit to indicate that you want Shorewall to add the alias with this name (e.g., "eth0:0"). That allows you to see the alias with ifconfig. That is the only thing that this name is good for -- you cannot use it anywhere else in your Shorewall configuration.

Each interface must match an entry in shorewall-interfaces(5). Shorewall allows loose matches to wildcard entries in shorewall-interfaces(5). For example, ppp0 in this file will match a shorewall-interfaces(5) entry that defines ppp+.

If you want to override ADD_IP_ALIASES=Yes for a particular entry, follow the interface name with ":" and no digit (e.g., "eth0:").

INTERNAL - address

Internal Address (must not be a DNS Name).

ALL INTERFACES (allints) - [Yes|No]

If Yes or yes, NAT will be effective from all hosts. If No or no (or left empty) then NAT will be effective only through the interface named in the INTERFACE column.

LOCAL - [Yes|No]

If Yes or yes, NAT will be effective from the firewall system


DNAT rules always preempt one-to-one NAT rules. This has subtile consequences when there are sub-zones on an interface. Consider the following:


#ZONE   TYPE    OPTIONS                 IN                      OUT
#                                       OPTIONS                 OPTIONS
fw      firewall
net     ipv4
loc     ipv4
smc:net ipv4


net     eth0            dhcp,tcpflags,nosmurfs,routefilter,logmartians,sourceroute=0
loc     eth1            tcpflags,nosmurfs,routefilter,logmartians


#ZONE   HOST(S)                                 OPTIONS
smc     eth0:


#EXTERNAL       INTERFACE       INTERNAL        ALL             LOCAL
#                                               INTERFACES     eth0  

Note that the EXTERNAL address is in the smc zone.


#ACTION         SOURCE          DEST            PROTO   DEST    SOURCE          ORIGINAL        RATE            USER/   MARK    CONNLIMIT       TIME            HEADERS     SWITCH           HELPER
#                                                       PORT    PORT(S)         DEST            LIMIT           GROUP
DNAT            net             loc:  tcp     80

For the one-to-one NAT to work correctly in this configuration, one of two approaches can be taken:

  1. Define a CONTINUE policy with smc as the SOURCE zone (preferred):

    smc		$FW		CONTINUE
    loc		net		ACCEPT
    net		all		DROP		info
    all		all		REJECT		info
  2. Set IMPLICIT_CONTINUE=Yes in shorewall.conf(5).




shorewall(8), shorewall-accounting(5), shorewall-actions(5), shorewall-blacklist(5), shorewall-hosts(5), shorewall_interfaces(5), shorewall-ipsets(5), shorewall-maclist(5), shorewall-masq(5), shorewall-netmap(5), shorewall-params(5), shorewall-policy(5), shorewall-providers(5), shorewall-proxyarp(5), shorewall-rtrules(5), shorewall-routestopped(5), shorewall-rules(5), shorewall.conf(5), shorewall-secmarks(5), shorewall-tcclasses(5), shorewall-tcdevices(5), shorewall-mangle(5), shorewall-tos(5), shorewall-tunnels(5), shorewall-zones(5)


Frequently Used Articles

- FAQs - IPv4 Manpages - IPv6 Manpages - Configuration File Basics - Beginner Documentation - Troubleshooting

Shorewall 4.0/4.2 Documentation

Current HOWTOs and Other Articles

- 6to4 and 6in4 Tunnels - Accounting - Actions - Aliased (virtual) Interfaces (e.g., eth0:0) - Anatomy of Shorewall - Anti-Spoofing Measures - AUDIT Target support - Bandwidth Control - Blacklisting/Whitelisting - Bridge/Firewall - Building Shorewall from GIT - Commands - Compiled Programs - Configuration File Basics - DHCP - DNAT - Dynamic Zones - ECN Disabling by host or subnet - Events - Extension Scripts - Fallback/Uninstall - FAQs - Features - Fool's Firewall - Forwarding Traffic on the Same Interface - FTP and Shorewall - Helpers/Helper Modules - Installation/Upgrade - IPP2P - IPSEC - Ipsets - IPv6 Support - ISO 3661 Country Codes - Kazaa Filtering - Kernel Configuration - KVM (Kernel-mode Virtual Machine) - Limiting Connection Rates - Linux Containers (LXC) - Linux-vserver - Logging - Macros - MAC Verification - Manpages (IPv4) (IPv6) - Manual Chains - Masquerading - Multiple Internet Connections from a Single Firewall - Multiple Zones Through One Interface - My Shorewall Configuration - Netfilter Overview - Network Mapping - No firewalling of traffic between bridge port - One-to-one NAT - Operating Shorewall - OpenVPN - OpenVZ - Packet Marking - Packet Processing in a Shorewall-based Firewall - 'Ping' Management - Port Forwarding - Port Information - Port Knocking (deprecated) - Port Knocking, Auto Blacklisting and Other Uses of the 'Recent Match' - PPTP - Proxy ARP - QuickStart Guides - Release Model - Requirements - Routing and Shorewall - Routing on One Interface - Samba - Shorewall Events - Shorewall Init - Shorewall Lite - Shorewall on a Laptop - Shorewall Perl - Shorewall Setup Guide - SMB - SNAT - Split DNS the Easy Way - Squid with Shorewall - Starting/stopping the Firewall - Static (one-to-one) NAT - Support - Tips and Hints - Traffic Shaping/QOS - Simple - Traffic Shaping/QOS - Complex - Transparent Proxy - UPnP - Upgrade Issues - Upgrading to Shorewall 4.4 (Upgrading Debian Lenny to Squeeze) - VPN - VPN Passthrough - White List Creation - Xen - Shorewall in a Bridged Xen DomU - Xen - Shorewall in Routed Xen Dom0

Top of Page